What do you mean by a DIY-kit?

To save some money you can decide to build your speakers or amp by yourself. Besides the saving money part, creating a productby yourself can also be very satisfying. When you decide to buy a DIY-kit the product comes with clear step-by-step instructions.

What is included in a DIY-speaker kit?

A speaker kit consists of all parts exclusive wood. Typically it consists of:
  • 1 pair wideband drivers
  • 1 pair tweeter horns
  • 1 pair 15" woofer drivers (Jimi kit only)
  • electronic parts for the filter
  • damping material (not applicable for the Jimi kit)
  • internal wiring
  • speaker terminals
Assembly instructions can be found here.

What is included in a DIY-passive speaker pannel kit?

All parts that are included in the standard DIY-speaker kit, see above, plus:
  • cutted 24mm birch plywood panels for the speaker cabinets
  • premade cut-outs for drivers and tweeters
  • lamello-connectors for easy assembling
  • 1 pair floor platters
  • 2x3 feet for in between the floor platters and cabinets
Wood glue and furniture oil/wax is not included. For the specific contents of the kit of your choice please check out the DIY package content in the tab Specifications. 

We are currently working on DIY-kit for the Jimi open baffles. Please contact us if you want to more information.

Do the drivers need to be burned in?

The speaker- kits need two different kinds of burn- in:

- The burn- in of the wideband drivers suspensions need to be done before the drivers get mounted into the cabinets. For this a low frequent sine wave signal of 30Hz or lower is required because it protects the voicecoils from over- heating. Best is to place the drivers face-to-face, one driver connected out of phase and wobble- in the suspensions nonstop 24h/day for a couple of days. The Janis wideband drivers need a total cone- movement of about 8mm (+/-4mm), the Kurt speakers need a total cone- movement of about 1,5cm (+/-6mm to +/-8mm) and the Amy wideband drivers need a total cone- movement of about 2cm (+/-8mm to +/-12mm). This wobble- in guarantees the right function of the drivers in the bass horn-cabinets and is essential to get a good sounding pair of speakers.

- The burn- in of the cones doesn`t require special methods, listen music at low or high levels is fine. The wideband drivers cones themselves need to soften up to sound as expected because they work as bending wave- drivers to higher frequencies and show an early but controlled and smooth break- up. Depending on the speaker- model it takes about 300hours to 500hours until the burn- in is complete. The speakers need about one week of normal listening before the midrange starts to smoothen up and the speakers play music. During the first two or three month the speakers will show additional improvements in the sound quality every day until the burn- in is complete.

I have bought a product that has parts missing, what to do?

Please contact us via mail and let us know hwat parts are missing. Please also provide us your invoice number.

What is a crossover less wideband driver?

There are no series crossover- parts before the driver in the signal- path and by this the driver is direct coupled to the amp for best possible control. A crossover less wideband- driver shows best possible detail and response because there is no loss of fine detail by any parts

What is a floor- firing bass horn?

It is an opening (horn- mouth) at the bottom of the speaker where the bass- waves come out produced by the wideband driver leave the cabinets after they have been transformed by the horn inside the cabinet. The floor- firing bass horns increase the dynamics a lot compared to traditional speakers because they act like much bigger diameter drivers. This is due to the much bigger surface of the horn- mouth. The floor-firing horns use the free floor space under and around the speakers as virtual part of the horn- mouth and so the speakers can produce fundamental bass and much higher dynamics compared to common speakers with same sized drivers. The floor- firing bass horn speakers react self- adjusting. Placed in a small room close to the rear- wall the floor- space under the speakers and around is smaller compared to free placement in a big room and the degree of the support of the horns is smaller. The floor- firing bass horn speakers won`t produce fat and muddy basses in small rooms and they won`t thin out and miss basses in bigger sized rooms.

What type of amp is best to use?

Any good sounding amp is fine to power the speakers! It`s a common misunderstanding that high efficient speakers require fly- powered tubed amps - it`s impossible that a powerful and fine sounding Solid State- amp which powers low efficient speakers sounds worse powering much more easy to drive high efficient speakers. On the other side there are many excellent sounding fly- powered amps and only very few speakers which are in 100% harmony to this amps. The high efficient speakers from the Club-27 line are great for this kind of amps. Beside the high efficiency of the speakers they are an easy load for any kind of amps and they show a flattened impedance- curve.

How to position the speakers?

The speakers should be positioned about 30cm before the rear- wall and pulled out from there in small steps until voices and solo- instruments rise in height and the image becomes three- dimensional. This behavior depends on the quality of the record and the electronics and if this position can`t be found the right distance to the rear- wall is where the midrange sounds best. The speakers can be placed relatively close to the wall and also relatively close to the listening- position. It`s also possible to place the speakers in parallel for wide and big imaging or to toe them in that the inner side of the cabinets is just visible from the listening- position to get the most sharp midrange- image.
The distance in between the speakers should be about the distance to the listening- position but this also is variable. The ideal position always is dependent on the room, on the electronics and on the personal preferences of the listener.

Which room size is best for what speaker?

The small Janis speakers sound best in small to medium sized rooms and they can be placed directly before the wall. The bigger speakers from the line can be placed in small rooms without producing boomy basses and they can fill even big room- spaces with beautiful sounding music and lots of dynamic- headroom.